Shopping Cart Items
You're looking for items filed under a category of 66 Tripower. There are 70 products in this category.
Page 3 of 3
« First ‹ Previous123
| Image | Description | Price |
|---|---|---|
 | Quality accelerator pumps, end carbs 59-66 and center carb 66 These are top quality pumps. Most important, they are Ethalnol resistant. If your pumps have a black cup (rubber part,) do not use them. They will only last a few weeks with Ethanol fuel. Additionally, you will note these pumps have the "garter spring" around the inside of the cup to help them last longer. And, they come assembled with a new spring and cap to hold the spring in place. These are the best pumps I can find. I use them in all my restorations.... (Read More) | $7.00 |
 | Needle and Seat replacements..Disc Valves This is a modern one piece replacement for your needle and seat. You can install them with a deep socket, rather than a straight screwdriver. Captured inside the unit is a disc that is activated by a small shaft that contacts the float at the same location as the old "needle." I ran them in my car and have sold many with positive feedback. I use them in all the restorations I complete.... (Read More) | $6.00 |
| PCV Grommet GM part This is the soft rubber grommet that is in the valley pan. The PCV Valve pushes into this grommet. They get hard and brittle with age and should be replaced.... (Read More) | $5.50 |
| 1959-1966 End carb Torsion Springs Sold in pairs. These are the medium duty springs for mechanical linkage cars. E-mail me if you need H.D. Springs.... (Read More) | $5.00 |
 | Vacuum nipple This parts is used to obtain vacuum (usually for advance) off the rear of the center carb. Brass.... (Read More) | $5.00 |
 | 66 choke pull-off rod This is the short rod from the choke pull-off diaphram to the lever on the end of the choke shaft.... (Read More) | $5.00 |
 | Alternator Strap Bolt/Stud This is used on the driver's side bolt that attaches the thermostat housing (waterneck.) This is a correctly made part, one piece. Most suppliers sell one with a two piece design that is far from correct.... (Read More) | $4.50 |
| Yellow Return Spring, GTO only This spring extends from center carb linkage to the throttle cable bracket.... (Read More) | $4.25 |
| Throttleblade (Butterfly) Brass Screw Set A must have when removing the throttleblades and choke flap. Set of 14. 12 have Phillips head, unlike originals. The two visible ones for choke flap have slotted head, while quantities last.... (Read More) | $4.00 |
| Air Cleaner Chrome Wingnuts Excellent Reproduction Of OEM Part. If you need all three studs and three chrome eingnuts, this item is offered on the page at a savings. This set described is for the GTO style air cleaners.... (Read More) | $3.50 |
| Set Zinc Plated (Gold) nuts to attach carbs Set of 12. The factory used steel nuts, so these are not "correct." But, they really do make a nice finishing touch. I use these on all the tripowers I restore.... (Read More) | $3.00 |
| 1966 Choke Stove Bolt/Washer Attaches choke stove. Phillips head bolt same as original, with special washer, also SS. Factory bolt was steel and rusted with the heat in this area. ... (Read More) | $3.00 |
| air cleaner studs/large air cleaner 59 to 66 Correct bottleneck stud. Shorter than the stud for the small, GTO style air cleaners.... (Read More) | $3.00 |
| Air cleaner Bottleneck Studs/Small GTO style cleaners Excellent reproduction of originals. If you need all three studs and all three wingnuts, this item is available on the page for a savings.... (Read More) | $2.50 |
| Block off plate gasket only Gasket between block off plate and intake.... (Read More) | $2.50 |
| Carb to Intake Gaskets Top Quality. Specify which carb and quantities as you place in cart.... (Read More) | $2.25 |
| Airhorn to Floatbowl Gasket Often needed after removing airhorn to replace jets, set floats, or to replace a wet gasket. I have never seen this gasket sold separately. Top Quality. When you add to cart, you can specify which carb. Smaller center carb takes different gasket, of course.... (Read More) | $2.00 |
| Air cleaner to carb gaskets Come in two sizes. Small for the 59 to 65 center carbs and the 57 and 58 carbs. The large size is for the 59 to 66 ends and the 66 center. You can choose size and number when you place items in the cart. These gaskets are seldom in the carb kits others sell. They are included in the kits I sell on the page.... (Read More) | $1.00 |
| throttlebody to floatbowl gasket 1966 center carb This gasket is proc 1/16" thick andhas the vent slots, as almost all do. There is a lot of confusion about thses slots. They do not create a vacuum leask as they are above the throttleblades. They vent vapors that build up behind the throttle blades at hot idle.... (Read More) | $0.95 |
| throttlebody (base) to floatbowl gaskets, large end carbs This is the gasket between the cast iron throttlebody and the floatbowl. They do not have vent slots. Factory used this gasket. However, there are no problems using the gasket in this location with the vent slots. ... (Read More) | $0.75 |
Page 3 of 3
« First ‹ Previous123
